|
Cat No |
Description |
Specification |
|
ONC-022
|
Corridor Displays with Controls
|
- Designed to indicate incoming calls in corridors, staff rooms etc.
- Shows call type (e.g. PIR call), location (e.g. bedroom #2) and depending on the device making the call, the name of the person calling.
- Can also be used on conventional and addressable call systems.
|
|
ONC-024
|
Slave Overdoor Light
|
- Indicates the status of the ONC-087 master dementia controller by pulsing red and/or green as appropriate.
- Allows staff to see at a glance if assistance is required.
- Pulsing frequency and light sequence changes/increases with call level.
- Can also be used on conventional and addressable call systems.
|
|
ONC-033
|
Infrared/Radio Staff Attack Transmitter (Push for Attack/Pull for Attack)
|
- Allows staff to call for extra assistance or signal an ‘attack’ situation via a ONC-050 infrared ceiling receiver.
- For use with infrared call points, infrared ceiling receivers and Mk2 radio receivers.
- Typical transmitting range is 10m in the line of sight.
- Rechargeable.
- Can also be used on conventional and addressable call systems.
|
|
ONC-042
|
PIR Movement Sensor (Requires an ONC-102 Power Interface)
|
- Can be programmed at the ONC- 087 controller to make a call when movement is detected (e.g. when a patient exits their bed) and to automatically switch lights on to ensure the patients safety.
- A maximum of two ONC-042s can be connected per PIR channel.
|
|
ONC-043
|
Super-Bright 3W MR16 LED Lamp
|
- Switches on, off or dims down dependent on the status of the behaviour pattern selected.
- Timer options are also available to guide patients in and out of ensuites.
- Up to two ONC-043’s can be connected per lighting circuit.
- LED lamp housings are not included.
|
|
ONC-044
|
Enuresis/Bed Exit Interface Socket
|
- Includes two remote jack sockets, one for an ONC-045 enuresis sensor and one for an ONC-047 bed exit mat or other ancillary calling device.
- Fully isolated and medical directive compliant.
- Requires a PP3 battery (not supplied).
|
|
ONC-045
|
Enuresis (Bed Wet) Sensor
|
- Triggers a call when moisture is detected in a patient’s bed.
- Typically placed between the bed sheet and mattress.
- Measures 80cm x 12cm and connects to an ONC-044 Enuresis/ bed exit interface socket.
- Can be wiped clean using a noncaustic sanitiser making it suitable for multiple use.
|
|
ONC-046
|
Interface Unit c/w Remote Socket
|
- Includes a remote jack socket that can be configured for normally open or normally closed operation.
- Typically used to connect ONC-047 bed exit mats or other ancillary calling devices that do not wish to use the enuresis (bed wet) sensing function.
|
|
ONC-047
|
Bed Exit Mat (Connects to an ONC-044 Interface Socket or ONC-046 Interface Unit)
|
- Senses the pressure change when a patient exits or returns to bed.
- Measures 80cm x 10cm and connects to an ONC-044 Enuresis/ bed exit interface socket or ONC- 046 interface unit.
- Typically placed horizontally between the bed sheet and mattress.
|
|
ONC-048
|
Chair Exit Mat (Connects to an ONC-044 Interface Socket or ONC-046 Interface Unit)
|
- Senses the pressure change when a patient exits or sits back down on a chair.
- Measures 40cm x 25cm and connects to an ONC-044 enuresis/ bed exit interface socket or ONC- 046 interface unit.
|
|
ONC-050
|
Round Slave Infrared Ceiling Receiver
|
- Designed to accept calls for extra assistance and/or ‘staff attack’ notifications generated by a member of staff’s ONC-033 infrared transmitter.
- Typical receiving range is 10m in the line of sight.
- Maximum 3 receivers per ONC-087 controller.
|
|
ONC-051
|
Room Status Controller (Magnetic Reset/Isolate)
|
- Allows staff to isolate certain functions (e.g. PIRs during daytime hours), to put the room into ‘presence’ and to reset calls using a magnetic swipe key.
- Allows carers to arm/isolate the system and reset any active calls. An optional door bell will trigger a call when pressed by the patient.
|
|
ONC-087
|
Dementia Care Controller
|
- Includes all of the inputs, outputs, timers and power required for the connection of system devices.
- Features two PIR sensing channels and two LED lighting circuits.
- Sends detailed room status data to all displays.
- Includes space for 1 x 12V 7Ah batteries (providing up to 8 hours standby time).
- Requires a 230Vac mains supply and connects to the system via its two network connection.
|
|
ONC-088
|
Room Status Controller (Keyswitch Reset/Isolate)
|
- Allows staff to isolate certain functions (e.g. PIRs during daytime hours), to put the room into ‘presence’ and to reset calls using a key.
- Allows carers to arm/isolate the system and reset any active calls. An optional door bell will trigger a call when pressed by the patient.
|
|
ONC-119
|
PIR Power Interface c/w Isolation Keyswitch
|
- For use with ONC-042 PIR movement sensors.
- Provides power for up to two ONC-042s without the need for a separate PSU.
|
|
Cat No
Description
Specification
|
ONC-022
Corridor Displays with Controls
- Designed to indicate incoming calls in corridors, staff rooms etc.
- Shows call type (e.g. PIR call), location (e.g. bedroom #2) and depending on the device making the call, the name of the person calling.
- Can also be used on conventional and addressable call systems.
|
|
Cat No
Description
Specification
|
ONC-024
Slave Overdoor Light
- Indicates the status of the ONC-087 master dementia controller by pulsing red and/or green as appropriate.
- Allows staff to see at a glance if assistance is required.
- Pulsing frequency and light sequence changes/increases with call level.
- Can also be used on conventional and addressable call systems.
|
|
Cat No
Description
Specification
|
ONC-033
Infrared/Radio Staff Attack Transmitter (Push for Attack/Pull for Attack)
- Allows staff to call for extra assistance or signal an ‘attack’ situation via a ONC-050 infrared ceiling receiver.
- For use with infrared call points, infrared ceiling receivers and Mk2 radio receivers.
- Typical transmitting range is 10m in the line of sight.
- Rechargeable.
- Can also be used on conventional and addressable call systems.
|
|
Cat No
Description
Specification
|
ONC-042
PIR Movement Sensor (Requires an ONC-102 Power Interface)
- Can be programmed at the ONC- 087 controller to make a call when movement is detected (e.g. when a patient exits their bed) and to automatically switch lights on to ensure the patients safety.
- A maximum of two ONC-042s can be connected per PIR channel.
|
|
Cat No
Description
Specification
|
ONC-043
Super-Bright 3W MR16 LED Lamp
- Switches on, off or dims down dependent on the status of the behaviour pattern selected.
- Timer options are also available to guide patients in and out of ensuites.
- Up to two ONC-043’s can be connected per lighting circuit.
- LED lamp housings are not included.
|
|
Cat No
Description
Specification
|
ONC-044
Enuresis/Bed Exit Interface Socket
- Includes two remote jack sockets, one for an ONC-045 enuresis sensor and one for an ONC-047 bed exit mat or other ancillary calling device.
- Fully isolated and medical directive compliant.
- Requires a PP3 battery (not supplied).
|
|
Cat No
Description
Specification
|
ONC-045
Enuresis (Bed Wet) Sensor
- Triggers a call when moisture is detected in a patient’s bed.
- Typically placed between the bed sheet and mattress.
- Measures 80cm x 12cm and connects to an ONC-044 Enuresis/ bed exit interface socket.
- Can be wiped clean using a noncaustic sanitiser making it suitable for multiple use.
|
|
Cat No
Description
Specification
|
ONC-046
Interface Unit c/w Remote Socket
- Includes a remote jack socket that can be configured for normally open or normally closed operation.
- Typically used to connect ONC-047 bed exit mats or other ancillary calling devices that do not wish to use the enuresis (bed wet) sensing function.
|
|
Cat No
Description
Specification
|
ONC-047
Bed Exit Mat (Connects to an ONC-044 Interface Socket or ONC-046 Interface Unit)
- Senses the pressure change when a patient exits or returns to bed.
- Measures 80cm x 10cm and connects to an ONC-044 Enuresis/ bed exit interface socket or ONC- 046 interface unit.
- Typically placed horizontally between the bed sheet and mattress.
|
|
Cat No
Description
Specification
|
ONC-048
Chair Exit Mat (Connects to an ONC-044 Interface Socket or ONC-046 Interface Unit)
- Senses the pressure change when a patient exits or sits back down on a chair.
- Measures 40cm x 25cm and connects to an ONC-044 enuresis/ bed exit interface socket or ONC- 046 interface unit.
|
|
Cat No
Description
Specification
|
ONC-050
Round Slave Infrared Ceiling Receiver
- Designed to accept calls for extra assistance and/or ‘staff attack’ notifications generated by a member of staff’s ONC-033 infrared transmitter.
- Typical receiving range is 10m in the line of sight.
- Maximum 3 receivers per ONC-087 controller.
|
|
Cat No
Description
Specification
|
ONC-051
Room Status Controller (Magnetic Reset/Isolate)
- Allows staff to isolate certain functions (e.g. PIRs during daytime hours), to put the room into ‘presence’ and to reset calls using a magnetic swipe key.
- Allows carers to arm/isolate the system and reset any active calls. An optional door bell will trigger a call when pressed by the patient.
|
|
Cat No
Description
Specification
|
ONC-087
Dementia Care Controller
- Includes all of the inputs, outputs, timers and power required for the connection of system devices.
- Features two PIR sensing channels and two LED lighting circuits.
- Sends detailed room status data to all displays.
- Includes space for 1 x 12V 7Ah batteries (providing up to 8 hours standby time).
- Requires a 230Vac mains supply and connects to the system via its two network connection.
|
|
Cat No
Description
Specification
|
ONC-088
Room Status Controller (Keyswitch Reset/Isolate)
- Allows staff to isolate certain functions (e.g. PIRs during daytime hours), to put the room into ‘presence’ and to reset calls using a key.
- Allows carers to arm/isolate the system and reset any active calls. An optional door bell will trigger a call when pressed by the patient.
|
|
Cat No
Description
Specification
|
ONC-119
PIR Power Interface c/w Isolation Keyswitch
- For use with ONC-042 PIR movement sensors.
- Provides power for up to two ONC-042s without the need for a separate PSU.
|